Author Topic: New 7.0.27 firmware available  (Read 5225 times)

Offline rafale77

  • Hero Member
  • *****
  • Posts: 1412
  • Karma: +71/-24
Re: New 7.0.27 firmware available
« Reply #15 on: July 18, 2018, 05:40:04 pm »
On the vera plus I just noticed it killed my zigbee network. I had to downgrade to recover... no joy.
openLuup (97 devices, 134 scenes, 20 apps) controlling HomeAss + VeraPlus (138 zwave nodes, 8 Zigbee nodes, 205 devices, 20 scenes , 2 app) Bridged to Homekit and Alexa. VeraPlus ExtRooted!

Offline picomo

  • Newbie
  • *
  • Posts: 5
  • Karma: +0/-0
Re: New 7.0.27 firmware available
« Reply #16 on: July 18, 2018, 11:48:26 pm »
Linear Garage door openers GD00Z-4 stopped working with latest firmware
Downgraded to 1.7.3831 and they are working again

Offline BrianLBeaton

  • Sr. Member
  • ****
  • Posts: 325
  • Karma: +12/-1
Re: New 7.0.27 firmware available
« Reply #17 on: July 19, 2018, 06:02:01 am »
My garage door opener (Linear GD00Z-4) works fine after upgrading to firmware 1.7.4001 on VeraPlus.

Offline timtownsend

  • Sr. Newbie
  • *
  • Posts: 27
  • Karma: +0/-0
Re: New 7.0.27 firmware available
« Reply #18 on: July 19, 2018, 01:49:24 pm »
Upgraded my VeraPlus, everything is fine. As far as I know I have no Zigbee devices, though.

I have a Zooz ZSE40 4-in-1 sensor that I had previously been unable to add, so I added it after upgrading to the new firmware. It added the 4 devices, but the temperature, humidity and light level all report incorrect values, and they never change. The motion sensor never reports any motion. Probably a bad sensor?

Offline rafale77

  • Hero Member
  • *****
  • Posts: 1412
  • Karma: +71/-24
Re: New 7.0.27 firmware available
« Reply #19 on: July 19, 2018, 01:58:09 pm »
Upgraded my VeraPlus, everything is fine. As far as I know I have no Zigbee devices, though.

I have a Zooz ZSE40 4-in-1 sensor that I had previously been unable to add, so I added it after upgrading to the new firmware. It added the 4 devices, but the temperature, humidity and light level all report incorrect values, and they never change. The motion sensor never reports any motion. Probably a bad sensor?

They probably haven't been configured yet. trying waking them up by poking at the wake button.
openLuup (97 devices, 134 scenes, 20 apps) controlling HomeAss + VeraPlus (138 zwave nodes, 8 Zigbee nodes, 205 devices, 20 scenes , 2 app) Bridged to Homekit and Alexa. VeraPlus ExtRooted!

Offline RV

  • Full Member
  • ***
  • Posts: 128
  • Karma: +0/-0
Re: New 7.0.27 firmware available
« Reply #20 on: July 20, 2018, 06:48:35 pm »
up to VeraPlus: 1.7.4001. this may have fixed my "16 alerts for 1 event" issue the started after the last update.

Offline anthonyris

  • Full Member
  • ***
  • Posts: 242
  • Karma: +6/-1
Re: New 7.0.27 firmware available
« Reply #21 on: July 22, 2018, 09:43:36 pm »
As previously reported, latest firmware upgrade once again resets manual network settings to ?Automatic? and turns Wifi radio back on. Also required power cycle after waiting 30 mins.

Reported here: http://forum.micasaverde.com/index.php/topic,81524.msg395120.html#msg395120

Vera3x2, Leviton, GE dimmers, relays and lamp modules, Sonos, Nests...

Offline RV

  • Full Member
  • ***
  • Posts: 128
  • Karma: +0/-0
Re: New 7.0.27 firmware available
« Reply #22 on: July 23, 2018, 05:01:50 pm »
it did not enable wifi for me

Offline 3rdStng

  • Full Member
  • ***
  • Posts: 117
  • Karma: +1/-0
Re: New 7.0.27 firmware available
« Reply #23 on: July 26, 2018, 08:08:40 pm »
Prior to my upgrade I was getting "Luup : Downloading Luup Plugins" messages. This started at the same time as the Firmware notifications, so I thought they were related. I took all my normal backups and clicked Upgrade. When the upgrade to 7.0.27.4001 on my VeraPlus completed, I was still getting those errors, plus a new one that my EventWatcher Startup Lua Failed. After cruising the forums I realized that my EventWatcher is REALLY old. So I removed it/uninstalled it and now I am getting even more Startup Lua Failures along with a system failure about EventWatcher. "System error : Device: 329. Fail to load implementation file D_EventWatcher.xml" Device 329 was an attempt to reinstall EventWatcher.

All this leads me to two questions.
1. How can I remove device 329 from the LUA startup?
2. I am getting System Errors trying to save scenes. The last time this happened I was out of storage. What can I safely clear up to free up a little room? I cannot even enable remote support.
Code: [Select]
System error : Device: 329. Fail to load implementation file D_EventWatcher.xml
Luup : Downloading Luup Plugins
Luup : Downloading Luup Plugins
Luup : Downloading Luup Plugins
Luup : Failed to download all plugins. Will retry in 10 minutes.
GCal3 Matt[134] : Startup Lua Failed
ERROR : Error in lua for scenes and events
GCal3 Holidays[224] : Startup Lua Failed

Filesystem                Size      Used Available Use% Mounted on
rootfs                    8.6M      8.4M    212.0K  98% /
/dev/root                10.0M     10.0M         0 100% /rom
tmpfs                   124.8M    364.0K    124.4M   0% /tmp
/dev/mtdblock7            8.6M      8.4M    212.0K  98% /overlay
overlayfs:/overlay        8.6M      8.4M    212.0K  98% /
tmpfs                   512.0K         0    512.0K   0% /dev
/dev/mtdblock10          50.0M      1.5M     48.5M   3% /storage
/dev/mtdblock10          50.0M      1.5M     48.5M   3% /etc/cmh-firmware
/dev/mtdblock10          50.0M      1.5M     48.5M   3% /etc/cmh-backup
/dev/sda1               487.9M      4.2M    447.8M   1% /tmp/log/cmh
/dev/mtdblock9           10.0M     10.0M         0 100% /mios

Offline Tsviper

  • Sr. Newbie
  • *
  • Posts: 48
  • Karma: +4/-0
Re: New 7.0.27 firmware available
« Reply #24 on: July 26, 2018, 09:13:48 pm »
Prior to my upgrade I was getting "Luup : Downloading Luup Plugins" messages. This started at the same time as the Firmware notifications, so I thought they were related. I took all my normal backups and clicked Upgrade. When the upgrade to 7.0.27.4001 on my VeraPlus completed, I was still getting those errors, plus a new one that my EventWatcher Startup Lua Failed. After cruising the forums I realized that my EventWatcher is REALLY old. So I removed it/uninstalled it and now I am getting even more Startup Lua Failures along with a system failure about EventWatcher. "System error : Device: 329. Fail to load implementation file D_EventWatcher.xml" Device 329 was an attempt to reinstall EventWatcher.

All this leads me to two questions.
1. How can I remove device 329 from the LUA startup?
2. I am getting System Errors trying to save scenes. The last time this happened I was out of storage. What can I safely clear up to free up a little room? I cannot even enable remote support.
Code: [Select]
System error : Device: 329. Fail to load implementation file D_EventWatcher.xml
Luup : Downloading Luup Plugins
Luup : Downloading Luup Plugins
Luup : Downloading Luup Plugins
Luup : Failed to download all plugins. Will retry in 10 minutes.
GCal3 Matt[134] : Startup Lua Failed
ERROR : Error in lua for scenes and events
GCal3 Holidays[224] : Startup Lua Failed

Filesystem                Size      Used Available Use% Mounted on
rootfs                    8.6M      8.4M    212.0K  98% /
/dev/root                10.0M     10.0M         0 100% /rom
tmpfs                   124.8M    364.0K    124.4M   0% /tmp
/dev/mtdblock7            8.6M      8.4M    212.0K  98% /overlay
overlayfs:/overlay        8.6M      8.4M    212.0K  98% /
tmpfs                   512.0K         0    512.0K   0% /dev
/dev/mtdblock10          50.0M      1.5M     48.5M   3% /storage
/dev/mtdblock10          50.0M      1.5M     48.5M   3% /etc/cmh-firmware
/dev/mtdblock10          50.0M      1.5M     48.5M   3% /etc/cmh-backup
/dev/sda1               487.9M      4.2M    447.8M   1% /tmp/log/cmh
/dev/mtdblock9           10.0M     10.0M         0 100% /mios

I had the same issues with every update since since about May...I have the DataMine 2 Plugin installed and it uses just enough space to fill it up.  This is how I solved my issue: http://forum.micasaverde.com/index.php/topic,81524.msg386059.html#msg386059

Hope this helps.

Offline 3rdStng

  • Full Member
  • ***
  • Posts: 117
  • Karma: +1/-0
Re: New 7.0.27 firmware available
« Reply #25 on: July 26, 2018, 09:21:15 pm »
Hmm. I do have that plugin too. But since I mounted a USB drive and stored all the logs there I didn't think that much room was being used.

Offline Dansker

  • Full Member
  • ***
  • Posts: 106
  • Karma: +0/-0
Re: New 7.0.27 firmware available
« Reply #26 on: July 27, 2018, 02:49:57 am »
Updated 1x Plus and 2x Edge with simple setups:

All took first time and the two Veras with most use report no Vera or luup reboots/restarts since installed 4 days ago (per SysMon). Encouraging, rarely would it run for 2 days.

Offline Tsviper

  • Sr. Newbie
  • *
  • Posts: 48
  • Karma: +4/-0
Re: New 7.0.27 firmware available
« Reply #27 on: July 27, 2018, 11:34:29 am »
Hmm. I do have that plugin too. But since I mounted a USB drive and stored all the logs there I didn't think that much room was being used.

I have the same setup with data being logged to a USB, however the plugin itself takes up 2.4mb which is quite large considering the partition is only about 8.6mb or so if I remember correctly.  That is about 28% of the partition just for this one plugin.  My guess is that anyone who has this plugin installed is having a similar problem.
« Last Edit: July 27, 2018, 11:37:25 am by Tsviper »

Offline rafale77

  • Hero Member
  • *****
  • Posts: 1412
  • Karma: +71/-24
Re: New 7.0.27 firmware available
« Reply #28 on: July 27, 2018, 11:51:46 am »
Hmm. I do have that plugin too. But since I mounted a USB drive and stored all the logs there I didn't think that much room was being used.

I have the same setup with data being logged to a USB, however the plugin itself takes up 2.4mb which is quite large considering the partition is only about 8.6mb or so if I remember correctly.  That is about 28% of the partition just for this one plugin.  My guess is that anyone who has this plugin installed is having a similar problem.

If storage space continues to be a problem, I am considering moving the rootfs of the vera to an external USB SSD.
https://wiki.openwrt.org/doc/howto/extroot
Not for the faint of heart but could be the solution.
openLuup (97 devices, 134 scenes, 20 apps) controlling HomeAss + VeraPlus (138 zwave nodes, 8 Zigbee nodes, 205 devices, 20 scenes , 2 app) Bridged to Homekit and Alexa. VeraPlus ExtRooted!

Offline RichardTSchaefer

  • Master Member
  • *******
  • Posts: 10091
  • Karma: +764/-142
Re: New 7.0.27 firmware available
« Reply #29 on: July 27, 2018, 11:56:49 am »
The right solution is for Vera to NOT release the OS every time ...
They need to break their current installation into:
    a) An OS piece
    b) A Vera piece
Then they olnly need enough space for the Vera Stuff  with each release ...
Then they can release an OS independent of the Vera Stuff and visa-versa.
Note: There is already a
    c) User/Controller specific piece that is supposed to survive an update