Author Topic: New 7.0.27 firmware available  (Read 4435 times)

Offline deepsnow

  • Newbie
  • *
  • Posts: 2
  • Karma: +0/-0
Re: New 7.0.27 firmware available
« Reply #45 on: August 09, 2018, 02:27:45 pm »
I started a new thread, but probably should have just posted in this thread. I am confused by the 7.0.27 firmware version, since I do not see that anywhere.

Anyway, everything was working perfectly until I did this update.

Now, my lights turn on at sunset, but never turn off. I have to manually reboot my Vera Plus every morning, then I can turn the lights off through the web interface.

I can see the event is being triggered like it should, but the communication seems lost with my z-wave LED bulbs until I reboot. I can still communicate with my door lock, so it is just my 3 z-wave light bulbs.

I have 4 of these Vera Plus units in 4 different homes. This is the only one I have upgraded. Soon I will not be at this house to reboot the controller every morning, so my home automation is no longer automated.

Any ideas?

Is there an automatic reboot scheduler I can run in the middle of the night that would simulate me rebooting the controller?

Can I downgrade firmware?

Any other things to try?

Thank you,
Scott

Offline HSD99

  • Sr. Member
  • ****
  • Posts: 282
  • Karma: +11/-0
Re: New 7.0.27 firmware available
« Reply #46 on: August 10, 2018, 04:30:07 pm »
7.0.27 is the release version. The specific software versions of 7.0.27 for each Vera controller are shown below:

https://support.getvera.com/customer/en/portal/articles/2944393

* Vera3, VeraLite, & VeraLite G: 1.7.1040
* VeraEdge: 1.7.4000
* VeraPlus: 1.7.4001
* VeraSecure: 1.7.4002

And yes, this is confusing.

Offline shawnky

  • Sr. Newbie
  • *
  • Posts: 24
  • Karma: +0/-0
Re: New 7.0.27 firmware available
« Reply #47 on: August 13, 2018, 08:40:55 pm »
I knew better than to update... I'll eventually learn... Lights = Orange Power, Green WAN...

Offline shallowearth

  • Hero Member
  • *****
  • Posts: 978
  • Karma: +46/-9
Re: New 7.0.27 firmware available
« Reply #48 on: August 21, 2018, 02:50:48 pm »
Hmm, Just updated to the latest firmware and I forgot the blue banner is now gone, is there a way to toggle it back on?  It is helpful to know when the engine is reloading, as if I try to do stuff (like edit a scene) while that is happening sometimes it toasts the Concord 4 plug in, so like to wait until the blue banner is complete before moving to a new task.  Can't do that if I can't see it :-)

Offline HSD99

  • Sr. Member
  • ****
  • Posts: 282
  • Karma: +11/-0
Re: New 7.0.27 firmware available
« Reply #49 on: August 21, 2018, 03:25:14 pm »
Yes. Go to Users & Account Info--->Notification Settings-----> Notifications Header (Additional diagnostic and operational messages displayed) and click the checkbox.

Offline ZW-Tom

  • Jr. Member
  • **
  • Posts: 55
  • Karma: +4/-1
Re: New 7.0.27 firmware available
« Reply #50 on: August 31, 2018, 05:01:07 pm »
For those in the know ...
Does anyone know where I can download a previous firmware version 1.7.3535 for VeraSecure?

I have been fighting 6 to 10 system reboots per day for 3 months now (most often at night between 3 a.m. and 8 a.m.), and support has not been able to fix it.

I did not have the problem until I upgraded to 1.7.3832 in May, and 1.7.4002 in August.

Thanks,
Tom