Author Topic: Aeotec Smart Switch 6 AU - Purging associations  (Read 3022 times)

Offline 3rdStng

  • Full Member
  • ***
  • Posts: 119
  • Karma: +1/-0
Re: Aeotec Smart Switch 6 AU - Purging associations
« Reply #30 on: November 04, 2018, 10:34:47 am »
That's cool and very nice of Chris. Out of curiosity, what did it cost to mail the switch? I need to outweigh if it's cheaper that route then buying a USB. I have a few Aeotec devices and plan to get more. If you don't recall or want say, what is the zip code you sent to and I can get the estimate.

Offline Spanners

  • Sr. Member
  • ****
  • Posts: 260
  • Karma: +16/-5
Re: Aeotec Smart Switch 6 AU - Purging associations
« Reply #31 on: November 09, 2018, 11:58:57 pm »
I contacted Aeotec for the firmware to resolve this (specifically the AU Version).

Chris Cheng sent me a file OTA_for Smart_Switch_6_AU_V1_00 (20150911).rar and advised me to downgrade the firmware to v1.00 resolve the issue.


Offline Qrp

  • Sr. Newbie
  • *
  • Posts: 22
  • Karma: +0/-0
Re: Aeotec Smart Switch 6 AU - Purging associations
« Reply #32 on: December 17, 2018, 09:10:32 am »
How do I read the version number of the SS6 firmware?

Thanks

Offline 3rdStng

  • Full Member
  • ***
  • Posts: 119
  • Karma: +1/-0
Re: Aeotec Smart Switch 6 AU - Purging associations
« Reply #33 on: December 17, 2018, 10:26:37 am »
How do I read the version number of the SS6 firmware?

From Aeotec support:
Code: [Select]
For Vera, you can determine firmware version using these steps:

Click on the main node of the DEVICE under "Device" page in Vera.
Go to Advanced -> Variables
Look for "VersionInfo"
The last 3 digits on the right side will tell me what firmware version you are running.

I was sent the firmware for 1.03 and 1.06. The newer features of 1.06 are not supported in Vera, yet. However I'm not using any newer features, so I loaded 1.06. Chris recommended downgrading to 1.03. Which I may still. After about 10 days of running firmware 1.06, the plug itself locked up. It would not manually turn on or off, what ever state it was in before, on or off, it remained in that state but the ring was displaying a dim purple. A unplug/plug resolves it and this has only happened once. If it happens again, I will downgrade.

Offline Qrp

  • Sr. Newbie
  • *
  • Posts: 22
  • Karma: +0/-0
Re: Aeotec Smart Switch 6 AU - Purging associations
« Reply #34 on: December 17, 2018, 11:09:06 am »
Under version number, I have 3,4,5,1,3

So I take that to be 1.03 perhaps?

Offline 3rdStng

  • Full Member
  • ***
  • Posts: 119
  • Karma: +1/-0
Re: Aeotec Smart Switch 6 AU - Purging associations
« Reply #35 on: December 17, 2018, 12:18:04 pm »
Under version number, I have 3,4,5,1,3

So I take that to be 1.03 perhaps?
That is correct. You have 1.03 if your version is ending in 1,3. I have one of each, 1.03 and 1.06, each showing 1,3 or 1,6 respectfully.