We have moved at community.getvera.com

Author Topic: Beta 1.5.408 - Repair report - hover not working  (Read 3517 times)

Offline BOFH

  • Sr. Hero Member
  • ******
  • Posts: 2409
  • Karma: +112/-140
Beta 1.5.408 - Repair report - hover not working
« on: July 06, 2012, 07:07:19 pm »
Vera2 - UI5 - beta firmware 1.5.408
When going to Setup -> Z-Wave settings -> Repair - View Repair Report

At the top of the report it states 'Hover over any device to see the other devices that can see it'. I hovered over every part of each entry but nowhere did it show me the other devices. Am I doing something wrong, or is this not active in this beta yet?

Please see attached screen shot and let me know where I am supposed to hover to get the devices that can see this one? As I'm trying to figure out why Schlage lever lock barely has 1 star signal strength and the Schlage deadbolt almost next to it has 4. The lever is actually closer to a cluster of 3 GE devices. (2 switch/1 dimmer only about 4 feet away)

My first repair/heal after upgrading to the new firmware presented the lever lock with 1 star and not being able to be configured. When I ran another repair for the lever only, it got configured. Previously it had 3 stars and no issues configuring.

 
Vera3 UI5 UI7 Edge Plus
Trane TZEMT400AB32 | Schlage BE369 FE599 | GE 45601 45602 45603 45604 45606 45609 45631 | Intermatic HA01C HA03C HA05C HA07C CA600 CA3000 | Aeon DSC06106 | Telguard GDC1 | Foscam FI8910W FI8905W FI9821W | D-Link 930L | Wanscam JW0011 | ZModo ZPIBH13W

Offline frichter09

  • Sr. Member
  • ****
  • Posts: 397
  • Karma: +0/-1
Re: Beta 1.5.408 - Repair report - hover not working
« Reply #1 on: July 08, 2012, 08:31:44 pm »
Not sure what the issue is but I never get anything if I hover over any device....
Vera Lite (1), Kwikset Locks (2), 2Gig-CT30 Thermostat (1), D-Link IP Cam (1), Evolve DM-15 (1), Evolve LRM-15(AS) (4), Evolve LFM-20 (1), Evolve LSM-15 (1), Everspring Sensor (1), Intermatic HA02C (6), Intermatic HA03C (4), Wayne-Dalton HA-03WD (2), MCV Smart Switch (1)

Offline svaleb

  • Hero Member
  • *****
  • Posts: 508
  • Karma: +11/-7
Re: Beta 1.5.408 - Repair report - hover not working
« Reply #2 on: December 29, 2012, 07:11:46 am »
No, I dont get anything either using this "hoover".
Why is the texst not deleted if it does not work.
Regards CE

Offline svaleb

  • Hero Member
  • *****
  • Posts: 508
  • Karma: +11/-7
Re: Beta 1.5.408 - Repair report - hover not working
« Reply #3 on: February 05, 2014, 08:22:14 am »
This seems to work now, in ui6. Even in explorer.
Took a while.
But difficult to owerview if you have several devices.
CE
And it stopped working again 3. of March.
Maybe because I went from 2.78 to 3.20.
Too bad.
CE
« Last Edit: March 05, 2014, 05:31:54 pm by svaleb »