Author Topic: d-link DCH-Z110  (Read 4891 times)

Offline CelticWebs

  • Sr. Member
  • ****
  • Posts: 250
  • Karma: +10/-7
Re: d-link DCH-Z110
« Reply #15 on: April 11, 2016, 09:40:44 am »
Unfortunately changing Variable 7 to 16, 20 and 22 and none result in a working Door & Window sensor.

Doe anybody actually have this sensor setup and working on their UI7 Vera?  I'm on a Vera plus but I don't believe the plus bit would effect the settings.

Any further help would be very much appreciated, I don't want this thing to beat me!

Many thanks

Offline sibay

  • Newbie
  • *
  • Posts: 4
  • Karma: +0/-0
Re: d-link DCH-Z110
« Reply #16 on: April 28, 2016, 03:09:43 pm »
Hi CelticWebs,

i just bought a DCH-Z110 and had problems with the door sensor. I followed the description from psixilambda. I dont know what this makes, but it works.

>Click the general sensor, then select device options, add configuration setting. Variable 7, 1 byte dec, desired value: 16.


Offline CelticWebs

  • Sr. Member
  • ****
  • Posts: 250
  • Karma: +10/-7
Re: d-link DCH-Z110
« Reply #17 on: April 28, 2016, 04:00:31 pm »
Interestingly for me this did not work.  After a lot of investigation we discovered that on my Vera plus, the communication with the main device was encrypted (zwave plus) but the child devices, door, light and temperature was unencrypted and Vera was seeing them report but ignoring them.

Further investigation showed that the device used a multi command class.  Disabled the multi command class by setting variable 6 to 54 and everything started working perfectly, light and temperature sensors update as light and temperature change and the door sensor now works perfectly too :).

Maybe there's variations of firmware for the dlink.  Are you in Europe sibay?

Offline MichuP

  • Newbie
  • *
  • Posts: 2
  • Karma: +0/-0
Re: d-link DCH-Z110
« Reply #18 on: March 19, 2017, 02:34:52 am »
Hi everyone, my first post here. Nice to meet you.
I found good explanation for D-link sensors configuration in Vesternet site. It works well in Vera Plus.
Dch-z110: http://www.vesternet.com/resources/application-notes/apnt-136

Dch-z120:
http://www.vesternet.com/resources/application-notes/apnt-135

By the way I have problem with association D-link Dch-z120 PIR sensor with Qubino 2x relay.
It doesn't work.
 In D-link there is parent device which make possible define association in device options. In embedded device 'motion sensor' isn't possible association definition. Only motion sensor detects movement and change state. I suppose that parent device doesn't send order to relay.

Anybody solve this kind of problem?

Scenes of course works well but controller has to be on line.
Regards

Wysłane z mojego ONEPLUS A3003 przy użyciu Tapatalka
« Last Edit: March 19, 2017, 02:44:09 am by MichuP »

Offline Domoworking

  • Newbie
  • *
  • Posts: 18
  • Karma: +0/-0
Re: d-link DCH-Z110
« Reply #19 on: April 15, 2018, 12:41:28 pm »
Thx MichuP
I configured my z110 as suggested in the link you posted, but I'm still struggling reading light and temperature.
It Always reports 1 Lux and 25? C...

Any suggestion?

Regards