We have moved at community.getvera.com

Author Topic: Assocoation Sunricher SR-ZV9003T4-RGBW-EU with Fibaro FGRGBWM-441  (Read 2135 times)

Offline jp

  • Newbie
  • *
  • Posts: 10
  • Karma: +0/-0
Hi,

I read topics how to make device association but I can not make a association with my Sunricher Wall Switch SR-ZV9003T4-RGBW-EU and my Fibaro FGRGBWM-441.

In my Generic IO Device Sunricher I have make a association Group ID 1 to my verra and a ID 2 to my device Fibaro but the association don't work.

In the documentation, the Sunricher device as Group ID 1 for lifeline and the ID 2 to 5 for the zone 1 to 4. I haven't any configuration on my Fibaro device.

I have test on the VeraLite with firmware 1.7.919 and the VeraPlus with firmware 1.7.2608 .

I have see on this forum some people have a Sunricher RGBW Wall Switch... Can you help me??

Sorry for my poor English.

Many thanks for your help.


Offline Slartibartfast

  • Hero Member
  • *****
  • Posts: 856
  • Karma: +378/-367
Re: Assocoation Sunricher SR-ZV9003T4-RGBW-EU with Fibaro FGRGBWM-441
« Reply #1 on: June 07, 2017, 01:08:45 pm »
Hi jp,

I assume you followed my write up for this and set up the association as I showed so I see no reason why this should not work. Try using all the association groups just to see if it is only one group. On the controller, press the zone button and then try the colour buttons on/off and the colour wheel.
Did you get the same ghost devices I did?
Devon UK 240V 50Hz
Now on Homeseer

Offline jp

  • Newbie
  • *
  • Posts: 10
  • Karma: +0/-0
Re: Assocoation Sunricher SR-ZV9003T4-RGBW-EU with Fibaro FGRGBWM-441
« Reply #2 on: June 07, 2017, 04:50:14 pm »
Hi Slartibartfast,

Many thanks for your interesset my problem :)

I haven't gost device... Just one device type urn:schemas-micasaverde-com:device:GenericIO:1 with a on / off button.
I have test the group id 2 to 5 and it's impossible to control my fibaro. I would prefer have gosht device and my Sunricher Wall device OK. :-)

Do you have a generic IO device to, or you have change the device type with other XML file?
Do you have the same firmware?

I go in the option tab, i create the group id 1, I click the zwave (I don't set a any value), I aplly and "Update Neigbor Nodes". In association i have Group ID 1, Set to: 1, Currently 4.
Group ID 2, Set to: 50 (My Fibaro id), Currently: 50...
 I Have "Configure node right now" to


My Sunricher have ID 63 and node 25:
In the option tab, all the parametres is OK and the variable Configured:Assoc 1,1;2,50;3,50 -> OK)

In luua debug I have error messages:

01   06/07/17 22:17:59.461   ZWaveNode::GetNonce node 25 cannot send request, abort (nil) <0x7609f520>
01   06/07/17 22:17:59.461   ZWaveNode::EncryptFrame m_iFrameID 410 cannot get nonce node 25 command class 0x85 command 0x1 <0x7609f520>
02   06/07/17 22:17:59.461   ZWaveSerial::Send m_iFrameID 410 type 0x0 command 0x13 sent ok - can't encrypt <0x7609f520>
01   06/07/17 22:17:59.462   ZWJob_SendData::Run done/fail job job#39 :assoc set 25grp 1 dev:63 (0x938688) N:25 P:13 S:7 took 2063 ms method 2 to node 25 command 133/1 failed 5 retries 0 of 2 <0x7609f520>
01   06/07/17 22:17:59.462   ZWJob_SendData::Run nonce collission job#39 :assoc set 25grp 1 dev:63 (0x938688) N:25 P:13 S:6 to node 25 retries 1 <0x7609f520>
01   06/07/17 22:18:00.102   ZWaveNode::DecryptMessage node 25 dev 63 failed and backup nonce is -181

2:18:00.103   XXX-ZWaveNode::DecryptMessage node 25 dev 63 len=8/28 m_iFrameID 417 good -181 command class 0x53 command 0x2f status 0x0 int nonce 0x9a 0x1b 0x1c 0x55 0x31 0x3d 0x18 0x92 (###U1=##) ext nonce 0x7e 0x8c 0xfa 0xf7 0xe8 0x3c 0x77 0xc7 (~####) temp key 0 auth key 0x93 0x5b 0x75 0x87 0x11 0x6c 0x35 0x5f 0xad 0x36 0x58 0xe9 0x7 0x22 0x38 0x8c (#[u##l5_#6X##"8#) mac 0x3f 0x51 0x2 0xe 0xa3 0xdb 0x63 0x64 0x5 0xe0 0xd6 0x53 0xa8 0xe2 0x97 0xd2 (?Q####cd###S####) data 0x7e 0x8c 0xfa 0xf7 0xe8 0x3c 0x77 0xc7 0x56 0x53 0x2f 0xeb 0x31 0x68 0x43 0x3a 0x8a 0x5 0x82 0x9a 0xf4 0x2d 0x5d 0x69 0x8a 0x2f 0x95 0xd5 (~####)

I hope you can help me...

Many many thanks in advance!!

Offline Slartibartfast

  • Hero Member
  • *****
  • Posts: 856
  • Karma: +378/-367
Re: Assocoation Sunricher SR-ZV9003T4-RGBW-EU with Fibaro FGRGBWM-441
« Reply #3 on: June 08, 2017, 04:00:20 am »
Hi jp,

Not at home until tomorrow so unable to test until then.
I do not remember having to change any device types when I installed this and I used generic device when including.
The fact that you do not have the ghost devices suggests that something is not correct as Vera support told me that they were appearing as part of the device functionallity and could not be removed. The fact that I had 4 ghosts suggest that they were associated with the association groups which is why association does not work whilst you do not have them.

Since doing my write up on this device I have moved over to Homeseer but I still have my Vera Pus to test this with. I will attempt this tomorrow/this weekend and let you know.

In the meantime, try excluding and re-including right next to Vera. If you get the ghosts then you are probably okay, if not then probably not.

Just for info to others with Homeseer, Homeseer have not yet adopted Sunricher devices and they do not work. Hopefully soon.
Devon UK 240V 50Hz
Now on Homeseer

Offline jp

  • Newbie
  • *
  • Posts: 10
  • Karma: +0/-0
Re: Assocoation Sunricher SR-ZV9003T4-RGBW-EU with Fibaro FGRGBWM-441
« Reply #4 on: June 08, 2017, 09:55:17 am »
Hi Slartibartfast,

Many thanks for your reply!

I think you're right with the ghost devices. It's a good way for a solution.

I have excluding/ re -including the device many time, on the veralite and veraplus and I haven't the 4 ghosts devices.. :(

I'have 5 Sunricher Wall controller and I have test with 3 differents and no ghost device  :(

Thank you for your next test and the result  ;)

Offline jp

  • Newbie
  • *
  • Posts: 10
  • Karma: +0/-0
Re: Assocoation Sunricher SR-ZV9003T4-RGBW-EU with Fibaro FGRGBWM-441
« Reply #5 on: June 08, 2017, 12:51:28 pm »
For your information...

I have test with the new Beta firmware and no 4 ghosts devices...

I have create 4 parents devices but when I have "Reconfigure Node" my 4 devices have disappeared  ;D

 :-[

Offline trygve

  • Jr. Member
  • **
  • Posts: 83
  • Karma: +5/-1
Re: Assocoation Sunricher SR-ZV9003T4-RGBW-EU with Fibaro FGRGBWM-441
« Reply #6 on: June 08, 2017, 04:31:18 pm »
I have one of these and I have: urn:schemas-micasaverde-com:device:SceneController:1

I've just installed mine and included it in my network but not hooked up the rgbw controller yet (going to use Fibaro rgbw).
Vera Edge. Qubino flush dimmers-, 10V dimmers-, flush relays-, flush shutters-, Sunricher touch panel-, RGBW touch panel, Secure thermostats & relays, HeatIt thermostats, Fibaro RGBW dimmers, Aeotec multisensors-, Switches, Z-Wave.Me Wall Controllers, SwiidInter Cord Switch, Velux Integra, Sonos

Offline Slartibartfast

  • Hero Member
  • *****
  • Posts: 856
  • Karma: +378/-367
Re: Assocoation Sunricher SR-ZV9003T4-RGBW-EU with Fibaro FGRGBWM-441
« Reply #7 on: June 09, 2017, 08:15:49 am »
Testing install of my Sunricher 4 zone RGBW controller onto my Vera Plus

1)  Add device
2)  Generic Z wave device
3)  Next on Vera and then button on back of Sunricher
4)  Vera advised success. Please wait
5)  Many seconds later I have devices as shown below.

Device type = urn:schemas-micasaverde-com:device:SceneController:1
Device file = D_SceneController1.xml
Device json = D_SceneController1.json
Capabilities = 211,156,1,4,1,6,L,R,B,RS,|89,90,94,96:4,112,114,115,122,133,134,142,
Multichannel capabilities =
1,1,6,94,37,32,133,89,142,91,43,44,
2,1,6,94,37,32,133,89,142,91,43,44,
3,1,6,94,37,32,133,89,142,91,43,44,
4,1,6,94,37,32,133,89,142,91,43,44,
3,1,6,94,37,32,133,89,142,91,43,44,

Please let me know if any other screen shots will help.

I have no spare RGBW receivers to test association but I will test with On/Off power socket


« Last Edit: June 09, 2017, 08:33:37 am by Slartibartfast »
Devon UK 240V 50Hz
Now on Homeseer

Offline Slartibartfast

  • Hero Member
  • *****
  • Posts: 856
  • Karma: +378/-367
Re: Assocoation Sunricher SR-ZV9003T4-RGBW-EU with Fibaro FGRGBWM-441
« Reply #8 on: June 09, 2017, 08:48:38 am »
Now added a TKB wall socket just for testing.
Added association group 2 to point to the socket.

Pressed and released zone 1 button
Then every time I press the main centre on/off button the socket turns on/off

Devon UK 240V 50Hz
Now on Homeseer

Offline jp

  • Newbie
  • *
  • Posts: 10
  • Karma: +0/-0
Re: Assocoation Sunricher SR-ZV9003T4-RGBW-EU with Fibaro FGRGBWM-441
« Reply #9 on: June 09, 2017, 10:39:40 am »
Hi,

Many thanks for your tests! This is really nice!

First I have make a reset of my Sunricher (Press and hold down ?Inclusion/Exclusion? key on the back of the remote for over 10s until the LED indicator shows 3 short blinks and 1 long blink)

For me:
1)  Add device
2) Generic Z wave device
3) Next on Vera and button on back of Sunricher (I have make test with long press on the the main centre on/off too)
4) Include finish
6) I have a GenericIO device type:urn:schemas-micasaverde-com:device:GenericIO:1, D_GenericIO1.xml and D_GenericIO1.json. Not a SceneController:1

Capability: 211,156,1,4,24,1,L,R,B,RS,|85,89S,90S,91S,94,108S,112S,114S,115S,122S,133S,134S,142S,152,159,

When I make the association, in the Option Tab on the Device, the association is correctly but I have this error in luaupnp log:

ZWJob_SendData::Run done/fail job job#25 :assoc get 21grp 2 dev:66 (0x10e2d18) N:21 P:13 S:7 Id: 25 took 11110 ms method 2 to node 21 command 133/2 failed 5 retries 0 of 2 <0x2ca49680>
01   06/09/17 16:26:21.091   ZWJob_SendData::Run nonce collission job#25 :assoc get 21grp 2 dev:66 (0x10e2d18) N:21 P:13 S:6 Id: 25 to node 21 retries 1 <0x2ca49680>
01   06/09/17 16:26:21.104   ZWaveNode::DecryptMessage node 21 dev 66 failed and backup nonce is -164 <0x2c249680>
01   06/09/17 16:26:21.105   XXX-ZWaveNode::DecryptMessage node 21 dev 66 len=8/28 m_iFrameID 284 good -164 command class 0xf6 command 0xaa status 0x0 int nonce ...
01   06/09/17 16:26:21.121   ZWaveNode::DecryptMessage node 21 dev 66 failed and backup nonce is -210 <0x2c249680>
01   06/09/17 16:26:21.122   XXX-ZWaveNode::DecryptMessage node 21 dev 66 len=8/28 m_iFrameID 289 good -210 command class 0x56 command 0xb4 status 0x0 int nonce...
01   06/09/17 16:26:21.126   ZWaveNode::DecryptMessage node 21 dev 66 failed and backup nonce is 0



The firmware of my Sunricher is 816,780,15763

Do you have the same Sunricher firmware? It's possible Sunricher have made a update of their module and there is problems now?





Offline Slartibartfast

  • Hero Member
  • *****
  • Posts: 856
  • Karma: +378/-367
Re: Assocoation Sunricher SR-ZV9003T4-RGBW-EU with Fibaro FGRGBWM-441
« Reply #10 on: June 09, 2017, 11:34:40 am »
Device info.
Devon UK 240V 50Hz
Now on Homeseer

Offline jp

  • Newbie
  • *
  • Posts: 10
  • Karma: +0/-0
Re: Assocoation Sunricher SR-ZV9003T4-RGBW-EU with Fibaro FGRGBWM-441
« Reply #11 on: June 11, 2017, 05:27:20 am »
Hello Slartibartfast,

Many thanks for yours infos!

It's not the same model? I have attach the PDF Manual ZV9003T-RGBW-EU4.pdf...

Is it better to contact the vera support or Sunricher support?

I think there is a new firmware in the Sunricher SR-ZV9003T4-RGBW and It may not be compatible  :(

Thank you!!

Offline Slartibartfast

  • Hero Member
  • *****
  • Posts: 856
  • Karma: +378/-367
Re: Assocoation Sunricher SR-ZV9003T4-RGBW-EU with Fibaro FGRGBWM-441
« Reply #12 on: June 11, 2017, 06:49:45 am »
jp

If it is new firmware then it is a shame that it has gone from working to non working.
I would try support from both sides but when talking to Sunricher you could refer them to my write up to show how it worked then.
« Last Edit: June 11, 2017, 08:37:23 am by Slartibartfast »
Devon UK 240V 50Hz
Now on Homeseer

Offline jp

  • Newbie
  • *
  • Posts: 10
  • Karma: +0/-0
Re: Assocoation Sunricher SR-ZV9003T4-RGBW-EU with Fibaro FGRGBWM-441
« Reply #13 on: June 11, 2017, 09:17:53 am »
Hi Slartibartfast,

Thank you for your answer, I have send a ticket at Vera.

I hope they can help me  :D

Offline jp

  • Newbie
  • *
  • Posts: 10
  • Karma: +0/-0
Re: Assocoation Sunricher SR-ZV9003T4-RGBW-EU with Fibaro FGRGBWM-441
« Reply #14 on: June 19, 2017, 03:13:58 pm »
Hello,

I have Vera Support contacted and they told me is all OK...

I have buy a fibaro FGD-212 dimer for test and I have make a association with the Sunricher and it works!!!

The problem is therefore the Fibaro RGBW-441...

I tested all values of the parameter 6 and 42 but  nothing...'( :'(

Is there anyone who has succeeded association a device with the fibaro rgbw-441?

Many many thanks!