Author Topic: Fibaro Single Switch 2, Can't Detect Device.  (Read 457 times)

Offline Kainen

  • Newbie
  • *
  • Posts: 5
  • Karma: +0/-0
Fibaro Single Switch 2, Can't Detect Device.
« on: August 13, 2017, 09:24:41 am »
Hi!

I'm on a clean install on a Vera Plus and upgraded the Firmware to the latest version this morning (1.7.3015)

I have about 30 devices installed and everything is working fine except my latest addition of a Fibaro Single Switch 2 (FGS-213 ZW5 v3.2) that constantly reports "Can't detect device".

When I flip the switch on or off it works and Vera says that the device is responding again... then a couple of minutes later it says "Can't detect device".

I read in a thread that setting CommFailure variable to 0 would help but this does nothing.

Anybody got a solution for this? It's highly annoying when Vera says that a device isn't working when it clearly is...

Thanks in advance for any help solving this issue!

Offline Kainen

  • Newbie
  • *
  • Posts: 5
  • Karma: +0/-0
Re: Fibaro Single Switch 2, Can't Detect Device.
« Reply #1 on: August 13, 2017, 09:25:49 am »
I should probably add that the device has never been working for me, not on the old firmware or the new...

Offline bjork

  • Newbie
  • *
  • Posts: 1
  • Karma: +0/-0
Re: Fibaro Single Switch 2, Can't Detect Device.
« Reply #2 on: September 23, 2017, 02:35:06 pm »
I have the exact same problem with the Fibaro Single Switches that I have. They work when controlling them, but go into "Can't Detect Device" mode shortly after. If any one has found a solution to this, please share it here.

Offline pls90

  • Full Member
  • ***
  • Posts: 215
  • Karma: +1/-0
Re: Fibaro Single Switch 2, Can't Detect Device.
« Reply #3 on: September 23, 2017, 04:48:39 pm »
same thing here. I have 2 of the single switches, one is ok, the other is on "can't detect" most of the time

Offline John M.

  • Administrator
  • Hero Member
  • *****
  • Posts: 506
  • Karma: +39/-3
    • getvera.com
Re: Fibaro Single Switch 2, Can't Detect Device.
« Reply #4 on: September 25, 2017, 07:10:32 am »
Hi there, to my knowledge, most of the issues with Fibaro switches and dimmers should be resolved in the latest betas.


Please check with our support team to see if there are still any recurrent bugs open with this device and if it's something else that needs to be reported and resolved.
John.M. ▾ Senior Customer Care Advocate
Vera Control, Ltd. ▾ Smarter Home Control  ▾ support@getvera.com ▾www.getvera.com ▾ +1 (866) 966-2272

HOURS OF OPERATION (Pacific Time Zone, UTC -8 )
Monday - Friday   12:00 am ? 06:00 pm
Saturday - Sunday   04:00 am ? 06:00 pm

Offline Iiro

  • Newbie
  • *
  • Posts: 1
  • Karma: +0/-0
Re: Fibaro Single Switch 2, Can't Detect Device.
« Reply #5 on: September 25, 2017, 11:42:50 pm »
I have the same problem with all the FGS-213 switches.

Offline TJ

  • Newbie
  • *
  • Posts: 1
  • Karma: +0/-0
Re: Fibaro Single Switch 2, Can't Detect Device.
« Reply #6 on: October 04, 2017, 02:45:43 pm »
Me too, same issue...

Offline tini

  • Newbie
  • *
  • Posts: 1
  • Karma: +0/-0
Re: Fibaro Single Switch 2, Can't Detect Device.
« Reply #7 on: October 05, 2017, 01:38:06 pm »
Hi I just upgraded my Vera Lite to the 7.0.23b (from 7.0.22) yesterday evening
My Fibaro FGS-213 still acts the same. I can control it (on/off) and it returns power consumption,
but it keeps saying "Can't Detect Device"

An upgrade to 7.0.23 did not help. Still the same.

/Tim
« Last Edit: October 14, 2017, 02:27:49 pm by tini »