Author Topic: Full Instructions: Setting up VeraSecure as a Home Security System  (Read 468 times)

Offline JTG

  • Newbie
  • *
  • Posts: 16
  • Karma: +1/-0
After complaining for a while, I gave up on Vera publishing or including this information or samples with the VeraSecure, so I sat myself down and figured it out for myself.  I now finally have this down to a science. I have set up 2 of these systems, one already in production with monitoring service, and the other running and slated for next month to add the monitoring service. This is the OVERVIEW (e.g., not quite step by step) on how I got a fully functional, monitored security system that works, and makes sense to non-geeky people (like my wife and daughter). By the way, most of this will work on any Vera ui17 controller, not just the VeraSecure.  This posting is a work in progress, so please PM me with edits or suggestions.

**note: I have cross-posted this article at the url below, and that one includes the sound files and LUUP codes**

This is the equipment list I used:
1. One VeraSecure Home automation controller ($300 available from Vera or Amazon)
2. A 2gig DW-10 sensor for each opening to protect ($20 each at Amazon)
3. Vera does now have a package on their website called "Security complete" that can jumpstart you with the VeraSecure, a camera, motion sensor, and 2 door/windows sensors for 350.00
4. One Aeon Labs 5 series doorbell ($60 at Amazon)
5. One used Android tablet you don't mind attaching to a wall (or $50 for a cheap new one)

Here are the steps to get up and running:
1. Get the controller running
      a. Create an account on, and enter the serial number of your controller to attach it to your account
      b. Unpack, plug in power, and use the included Ethernet cable to connect the controller to one of the LAN ports of your existing Internet Router. Follow the startup wizard, answer the questions to get the controller up and running.
2. Add the HouseModes plugin to the VeraSecure
3. In the modes section of the Vera, at the bottom, set to 45 seconds before reporting a trip, and set the VeraSecure device to "off" in home mode
4. Optional: Add any personally selected Zwave devices you want, following instructions.
5. Add the sounds to the doorbell speaker (PM me for mine)
    a.   Create/find a 30 second long "Arming" beeping sound
    b.   Create/find a 30 second long "SensorTrip" double-beeping sound
    c.   Create/find a short "Confirmation" beep sound
    d.   Attach the doorbell speaker to a computer, backup up the sound files on it, and replace them with your custom sounds.
6. Pair the doorbell device, document its device number, set it to play sounds once, test and document the sound file numbers
7. Create a manual scene for Arming the system that executes a luup code (PM me if you need the LUUP codes I used)
    a.   Play the arming sound files
    b.   Set HouseModes to away after a 20 second delay
8. Create a manual scene for Disarming the system that executes a luup code
    a.   Play the disarming sound file
    b.   Set HouseModes to home
9. Create a manual scene for Stay/Night mode that executes a luup code
    a. Play the confirmation sound file
    b. Set HouseModes to Stay
10. Add all of the sensors
    a. Use the "Add Veralink device" option to add each 2GIG device
    b. Document the TX number and location for each sensor, and save this in a chart just in case
    c. For pairing the DW10, you must hold in the tamper button (or close the case) to pair
    d. I recommend creating a room called "sensors" and adding each sensor to that "room"
11. Create a scene for entry while armed
    a. Add every sensor to the trigger as "if opened while armed"
    b. execute luup code to play that same long double beeping sound
12. Set up the tablet
    a.   Connect it to the VeraSecure's wifi
    b.   Install ImperiHome (pro recommended)
    c.   Set up a layout of at least 4 sections for arm, disarm, Stay, and status
      i.   Arm/Away section: run the arm scene
      ii.  Disarm section: run the disarm scene
      iii. Stay/Night section: run the stay/night scene
      iv. Status section: show HouseModes mode
    d.   Passcode protect the disarm and status buttons, and then the configuration
13. Test, Test, Test!!
« Last Edit: August 30, 2017, 02:41:56 pm by JTG »

Offline wilme2

  • Hero Member
  • *****
  • Posts: 1020
  • Karma: +18/-13
Re: Full Instructions: Setting up VeraSecure as a Home Security System
« Reply #1 on: August 30, 2017, 01:40:19 pm »
Wow, can't believe more wasn't built into the VeraSecure...  What you did looks good - thanks for posting.

I think if it was me, I would use PLEG scenes instead of traditional scenes.  That gives you better restart/crash protection.  Plus make it easier to troubleshoot...
Long Live UI5!

Offline JTG

  • Newbie
  • *
  • Posts: 16
  • Karma: +1/-0
Re: Full Instructions: Setting up VeraSecure as a Home Security System
« Reply #2 on: August 30, 2017, 02:30:25 pm »
Thanks for the feedback!! I haven't had any troubleshooting issues yet (fingers crossed); the luup codes are very simple. I played with RulesEngine at one point, but that had some critical bugs, and I had to let it go. I followed the KISS philosophy on this project, and basically only added the minimum changes/plugins to the OEM configuration to get it where I feel Vera should have when it shipped, or at least as a downloadable or wizard-based package.

Offline kartcon

  • Jr. Member
  • **
  • Posts: 75
  • Karma: +2/-0
Re: Full Instructions: Setting up VeraSecure as a Home Security System
« Reply #3 on: September 10, 2017, 07:57:12 pm »
Like JTG, I too built a very similar system but opted to use PLEG for all the controls and logic. I used almost exactly the same equipment as he did and performed many of the same steps. Where our two systems differ is in the mechanics of the logic and control. While I am not saying one or the other is better, I do believe that a PLEG based system offers much more control, flexibility and customization.
On my Vera Secure I have a room named Alarm System. This room contains an instance of PLEG dedicated to just the alarm system, the Vera Secure Siren, the House Modes plug-in, all the door and window sensors, a custom Virtual Panel plug-in control center, 3 virtual switches and two multi-switches and the Aeon Door Chime.
I modeled the alarm system after that of a hard wired DSC panel I had in another home (connected to a Vera 3). The primary goals were: 1-ease of use. My wife needed to be able to set or disable it with a degree in computer geek; 2-full feature set - Stay/Away/Home with door annunciation, zone bypass, partition bypass; and 3-full integration with Vera and my existing sensors, lights and controls.
The final product works very well with very little input from the occupants of the home. Modes are set by either a schedule or proximity. Our presence is detected using the I-Phone locator app and the Ping Sensor app. In combination, the two apps do a very good job of detecting our arrival and departure. If both apps fail to detect our arrival the Kwikset lock is used as a fallback to place the alarm in Home mode. It will also place the alarm in away mode by pressing the lock button. Additional codes for guests and pet-sitters flash the porch lights to signal the alarm is on or offline as necessary. All alarm state changes are pushed to both phones using Prowl so we know when the house is secure or someone is home.
The beauty of the system is in the visual information it provides using the Virtual Panel, Virtual Switches and Multi-switches. That said, I was not a big fan of Vera Secures sensor icons and wanted my system to be more visual. I created a custom icon set for the virtual panel and set up the multi-switches as indicators (using the LBT option to make them basically 'read only'). Screen shots of the entire room with all controls and the Virtual panel in several states are attached.
I will gladly share my experience with anyone looking to undertake a similar project. I will not post my PLEG reports for all to see but will PM the relevant parts for anyone that asks.
Hardware used: Vera Secure, Aeon Doorbell, DW-345 door/window sensors, Zooz 4in1 Multisensors, Foscam security cameras.
Software used: PLEG, Virtual Panel, Home Modes, Day or Night, i-Phone Locator, Push Notifications, Ping Sensor, Virtual Switch, Multi-Switch and Event Watcher.
Additional Tools: Adobe Photoshop, RBrowser and assorted Mac utilities.
« Last Edit: September 10, 2017, 08:00:22 pm by kartcon »