Author Topic: Honeywell Z-Wave thermostat no longer reporting TEMP in energy mode  (Read 240 times)

Offline nutshellml

  • Sr. Member
  • ****
  • Posts: 276
  • Karma: +4/-4
So I'm not sure if it was a recent firmware upgrade or something changed w/ Vera, but I now notice that when I enter my ENERGY mode on my thermostat, it doesn't update the TARGET temperature either on my Vera web app or phone.  I can see when I go into the device that it's in Energy mode and when I physically look at the thermostat it shows energy mode and the energy mode temp.  Something is happening that it's not reporting the target temp when in energy mode... Thoughts?

If I do a ENGINE RELOAD, once it's back up the correct temp is displayed and when changing from ENERGY MODE back to the normal schedule it updates immediately, it's just going form normal to energy.
« Last Edit: May 03, 2018, 10:48:18 pm by nutshellml »

Offline JohnRob

  • Full Member
  • ***
  • Posts: 248
  • Karma: +11/-4
HI,

I'm sorry I'm not able to help (I don't use the ENERGY mode) :(

However when you say 
Quote
a recent firmware upgrade
are you referring to the Thermostat or Vera?

Thanks,
John

Offline nutshellml

  • Sr. Member
  • ****
  • Posts: 276
  • Karma: +4/-4
When Vera was updated this past one.

It also messed up my Alexa and now shows Vera offline.

Offline wilme2

  • Hero Member
  • *****
  • Posts: 1173
  • Karma: +23/-13
So I'm not sure if it was a recent firmware upgrade or something changed w/ Vera, but I now notice that when I enter my ENERGY mode on my thermostat, it doesn't update the TARGET temperature either on my Vera web app or phone.  I can see when I go into the device that it's in Energy mode and when I physically look at the thermostat it shows energy mode and the energy mode temp.  Something is happening that it's not reporting the target temp when in energy mode... Thoughts?

If I do a ENGINE RELOAD, once it's back up the correct temp is displayed and when changing from ENERGY MODE back to the normal schedule it updates immediately, it's just going form normal to energy.

I have three of these and use energy savings mode a lot.  But I am not expecting to see the energy savings temperature setting in the GUI.  Meaning, for example, one of my ACs is in Energy Savings mode right now, and that set point is either 83 or 84 degrees - but the setpoint shown in the GUI is the 76 degrees of the normal mode.
Code: [Select]
Capabilities
211,156,0,4,8,6,L,R,B,RS,|32,39,49:3,64:2,66,67,68,69,114,133,134,
Edit
ManufacturerInfo
57,17,1
Edit
VersionInfo
4,3,42,2,0
Edit
Configured
1
Edit
NodeInfo
20,27,31,40,42,43,44,45,72,85,86,
Edit
SetPointInfo
H1,C1,F1,D1,
Edit
SupportedType
OF,H1,C1,RS,H2,C2
Edit
ConfiguredAssoc
Edit
ModeSetting
1:;2:;3:;4:
Edit
LastUpdate
1515356351
Edit
FirstConfigured
1515356351
Edit
Neighbors
1,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,19,20,21,22,23,24,25,26,27,28,29,30,32,33,34,35,36,37,38,39,40,41,42,43,44,45,47,49,50,51,52,53,54,55,58,59,
Edit
LastReset
1515356350
Edit
AssociationNum
1
Edit
ConsecutivePollFails
0
Edit
PollRatings
5.00
Edit
CurrentTemperature
79.00
Edit
LastRouteUpdate
1525686333
Edit
ModeStatus
CoolOn
Edit
ModeState
Idle
Edit
ModeStateForEnergy
1
Edit
Mode
Auto
Edit
TemperatureScale
1,1,2
Edit
CurrentSetpoint Heat
70.00
Edit
CurrentSetpoint
76.00
Edit
AllSetpoints
70.00,76.00,73.00
Edit
CurrentSetpoint Cool
76.00
Edit
PollOk
8419
Edit
LastPollSuccess
1525717323
Edit
LastNnu
1525676400,62
Edit
LastArr
1525676400,62
Edit
ModeTarget
CoolOn
Edit
EnergyModeTarget
EnergySavingsMode
Edit
EnergyModeStatus
EnergySavingsMode
Edit
Status
0
Edit
SetpointTarget
74.00
Edit
PollNoReply
2
Long Live UI5!  (OK finally made the switch to UI7 in January 2018, and am pretty happy....)