"Play nice" devices list

[rafale77]

Found another couple of devices which work well with the Vera:
The KAIPULE door sensor IM20-ZWAVE-USA although it requires manually configuring it as a door sensor
Also the Zooz leak sensor ZSE30

[rafale77]

Can now add the Grabber/Bali Autoview series of window coverings which are Z-wave Plus.

[Sorin]

Hello Rafale,


Thank you for the ongoing contribution.
I have added to the list the Zooz and Bali Somfy blinds as I have a few other confirmation sources.
KAIPULE door sensor IM20-ZWAVE-USA is still in the thread mentioned by you.


Thank you again.

[rafale77]

Hello Rafale,


Thank you for the ongoing contribution.
I have added to the list the Zooz and Bali Somfy blinds as I have a few other confirmation sources.
KAIPULE door sensor IM20-ZWAVE-USA is still in the thread mentioned by you.


Thank you again.

Not sure what thread you are referring to on the KAIPULE...

[Sorin]

I meant to say, that if someone gets here, it will still see it in the thread, mentioned by you.

[zedrally]

You can add the following Black Cat & Philio devices to the list.

https://www.blackcatcontrolsystems.com.au/Black-Cat-ZWBCL1-Single-Relay-in-Wall-Controller


https://www.blackcatcontrolsystems.com.au/Black-Cat-Z-Wave-240VAC-ZWBCL2-Double-Relay


https://www.blackcatcontrolsystems.com.au/In-Wall-Switch-Controllers/Black-Cat-Controllers/Black-Cat-Z-Wave-Blind-Shutter-Awning-Controller


https://www.blackcatcontrolsystems.com.au/Security-%20Sensors-CCTV-Detectors/Z-Wave-Enabled-Alarms/Black-Cat-Multi-Message-Centre


https://www.blackcatcontrolsystems.com.au/Security-%20Sensors-CCTV-Detectors/Z-Wave-Plus-PIR's/Black-Cat-4%20in-1-Sensor


https://www.blackcatcontrolsystems.com.au/Security-%20Sensors-CCTV-Detectors/Z-Wave-Plus-PIR's/BlackCat-Door-Window-Sensor


https://www.blackcatcontrolsystems.com.au/Security-%20Sensors-CCTV-Detectors/Z-Wave-Plus-PIR's/BlackCat-Z-Wave-Plus-PIR


https://www.blackcatcontrolsystems.com.au/Security-%20Sensors-CCTV-Detectors/Z-Wave-Plus-PIR's/Black-Cat-Flood-Sensor-Alarm

[laalves]

Hi,

You can also add the following devices:

- Heatit Z-Wave Thermostat: www.heatit.com/heating-control/floor-heating-thermostats/heatit-z-wave-thermostat/

- Doorbird D10X/D20X Series: www.doorbird.com

I have 2 x first, 1 x second and are working just fine.

Cheers, L

[Sorin]

Thanks everyone.


List updated

[gzappala]

I have two NYCE (NCZ-3010) Hinge Door sensors working flawlessly with VeraPlus UI7.

[Sorin]

Added, Thank you.

[gzappala]

Please also add: Zooz ZEN20 Z-Wave PLUS Smart Energy Power Strip

[Sorin]

Thanks,added

[zedrally]

John, please add Black Cat LED Dimmer (AU) ZWBCLD1 to the list.

[kdschlosser]

I want to comment that not all GE/JASCO switches work properly. Unless all functionality works it cannot be added to the list. there are dimmers that have 2 problems. when Vera heals the network it causes the lights to flash. and you are also not able to set the z wave ramping properties. These problems occur only when connected to a Vera I have tested it with 2 other z wave controllers and these problems do not occur.

[reneboer]

Hi,

Just added a couple of NEO Coolcam devices. Their power plugs (PN E-P16-A02-301) work, but when including them you must select the Generic Z-Wave device, do the inclusion as instructed (click button 3 times) and wait for the 60 second time to expire. Then pull the plug out of the socket, put it back in and the inclusion process will continue. Bit odd, but was the case with all three I added. All reporting etc seems to work nicely, even voltage and amps.

Their flood sensor (PN: E-D01-A4-310) got included as a generic IO device so I had to change the attributes. Category = 4, device_file D_FloodSensor1.xml, device_json D_FloodSensor1.json. Now it all works as it should.

Cheers Rene